Power Stop Brake Pad Installation
Free Brake Pads With Installation Code
Bicycle Brake Pad Installation
Brake Pad Install Near Me
Auto Brake Pads
Free Brake Pads With Installation Cost

Loosen the lug nuts on the wheel, then jack up the vehicle and place the jack stands underneath the. Free brake inspection Installation of new Wagner ThermoQuiet brake pads Resurface brake rotors $99.99 per axle It should be noted that it may be necessary to change front brake pads more often than rear ones since they endure more stress.

Still have questions? Contact our technical support: [email protected]

Starting January 1, 2021, the states of California and Washington will have new regulations on the books. Thanks to the Copper-Free Brake Initiative, it will soon be illegal to install brake pads that contain more than 5% copper. Both states will require copper-free brake pads by 2025. As a consumer, you might be wondering how these new laws. If you're in need of a brake service and inspection, look no further than Firestone Complete Auto Care, where we offer free brake inspections year-round, seven days a week. Bring your vehicle in and our tire and auto service professionals will perform a free brake inspection service that includes: Measurement of front and rear brake pad wear. Slide pads out towards the rear of the bicycle. If you cannot accomplish this using your fingers, feel free to use your needle nose pliers. Install each pad to the proper corresponding carrier. Each pad is labeled “Left” or “Right” and has an arrow indicating the forward direction in which the pad should be oriented.

The installation guide is for reference only. Please refer to the vehicle’s service manual or professional installer for complete instructions.

How To Install a PowerStop Brake Kit

Step 1: Tools

Have the following parts and specialty tools available before you start a pad and rotor installation:

Power Stop Brake Pad Installation

brake fluid (as specified in the owner’s manual)
brake component lube
a caliper piston compressor or C-clamp
a jack and jack stands rated for the vehicles weight
wheel chocks

We also recommend using safety glasses and gloves during the installation.

Step 2: Check Brake Fluid

Have the vehicle in the park position and make sure it is on a hard, level surface. Then, check the brake fluid level at the reservoir. The brake fluid reservoir should be about half full. Monitor the fluid level while compressing the caliper piston in step 9.

Step 3: Lift Vehicle

Before raising the vehicle, chock all wheels remaining on the ground, set the parking brake if the rear wheels will remain on the ground and loosen the lug nuts on the wheels just enough to break them free. Lift the vehicle and support it with jack stands using the proper jacking points specified by the manufacture.

Caution: Alwaysuse jack stands. Never attempt to work on an elevated vehicle held in placeonly by a hydraulic jack.

Step 4: Remove The Wheel

Remove the lug nuts and the wheel. It is best to work on one wheel at a time, leaving the other side intact as a point of reference. As a safety precaution, place the wheel/tire assembly under the vehicle at the nearest frame rail, suspension component or crossmember. In the event of a faulty jack stand, the wheel/tire will stop the vehicle from falling onto the ground.

Step 5: Inspect Brakes

After removing the wheel, inspect the brake components for any signs of leaks or damage.

Step 6: Remove Caliper

Remove the two caliper guide pin bolts that hold the caliper onto the bracket. Then, remove the caliper and support it using a brake caliper hanger or a regular wire coat hanger.

Caution: Always support the caliper. Never allow the caliper to hang from the brake hose. This can cause damage to the brake hose.

Step 7: Remove Pads & Caliper Bracket

Then, remove the two caliper bracket bolts along with the caliper bracket.

Step 8: Remove the Rotor

The rotor can now be removed. Before removing the rotor check for retaining screws. Some vehicles use retaining screws to hold the rotor onto the hub. These will need to be removed. Sometimes rust will make the rotor bind to the hub and a mallet will be needed to loosen it. Tap both the front and back side alternating left and right, top and bottom of the rotor.

Step 9: Compress the Piston

The next step is to compress the piston back inside the caliper. The piston has extended as the pad material wears. With new thicker pads, you must return the piston back inside the caliper body to give the thicker pads room for installation. Using a piston compressor or a large C-clamp, place a used brake pad over the face of the piston to protect the surface from marring, and begin compressing the piston. As you turn the handle on the clamp, it will increase pressure on the piston, until it becomes flush with the surrounding metal. Push the piston in slowly to prevent unsafe back pressure and damage to the ABS modulator, brake valving or master cylinder. Monitor the brake fluid reservoir level while compressing the caliper pistons to make sure it does not overflow. Then, loosen and remove the piston compressor or C-clamp used. It may be necessary to drain some fluid from the master cylinder reservoir.

NOTE: Many rear brakepistons cannot be retracted with a C-clamp as they screw in and out. This typeof brake piston will have two recessed notches and a caliper piston adjuster isused to compress the piston.

Free Brake Pads With Installation Code

Step 10: Clean the Rotor Hub

Clean any rust off the face of the hub mating surface with a wire brush and a hub cleaning kit. Upgrade vista to windows 10 free. Rust or debris on the hub can cause rotor runout and lead to wheel vibration. Apply a thin film of anti-seize to the face of the hub. This will make it easier to remove the rotor next time.

For more information on preparing the rotor hub for a brake kit install, check out this video:

Step 11: Clean the Rotor

Before installing the rotor, clean it with mild soap and water. Then, wipe it clean with a lint-free cloth. Now the new rotor can be installed.

Checking For Lateral Runout

When installing rotors, we recommend checking the lateral runout. This will tell you if any variation exists between the rotor and the hub to which it is mounted. Depending on the application, the maximum acceptable lateral runout can range from .003” to .005”. Always refer to the manufacture specifications for each application. If a variation exists, this is generally easy to correct by re-indexing the rotor one hole at a time. The goal is to reduce runout by finding the best position for the rotor. If the rotor is not properly indexed, it’s possible to have some vibration or pulsation issues and damage the rotors over time.

Keep this in mind if the rotor needs to be removed to perform any other services to the vehicle. Mark the position of the rotor relative to the hub before its removed to make sure it is re-installed in the same position.

Some vehicles use a retaining screw to hold the rotor into position on the hub. It is not possible to re-index this style of rotor.

Step 12: Install New Hardware

Remove the old hardware from the caliper bracket and use a wire brush to clean rust from the areas where the pads or hardware contact the bracket. This helps ensure the new hardware will sit correctly on the bracket. Then, inspect and replace all hardware as needed making sure to apply brake lube to the guide pins and pad contact points. Worn or damaged hardware can lead to noise or poor brake pad performance.

Step 13: Install Caliper Bracket & Brake Pads

Install the caliper bracket and torque the caliper bracket bolts to the manufacturer’s specifications